Motorola Razr Plus 2024 Razr 50 Ultra Teardown & Disassembly

Welcome to come back to the channel! Today, we're diving deep into the Motorola Razr Plus 2024, additionally widely used in a few regions because the Razr 50 Ultra. This teardown and disassembly guideline will walk you via each and every step had to take aside this foldable cell and spotlight key restoration insights. If you experience content like this, make sure you subscribe and click the notification bell so you are going to be notified each time I upload a new video. Also, in case you want any equipment for this teardown, cost out the hyperlinks in the description under.

Let's get all started by taking out the SIM tray. Taking a better examine the SIM tray, you could possibly see a black rubber gasket round the hole, which enables to shop water and filth out. This gasket is significant for holding the mobile’s IP rating.

Next, we desire to apply heat to either the outer screen and the ground cowl. You can use either a hairdryer or a heat gun to soften the adhesive underneath. I decide upon the usage of a hairdryer because it reduces the possibility of overheating and negative inner supplies. Once the adhesive is satisfactorily heated, use a pry instrument to moderately pry off the outer monitor and backside canopy.

With the screen and bottom hide got rid of, we will be able to see a Philip screw protecting down the quilt over the monitor connector. Remove this screw to get entry to the connector. It's worth noting that the glass digital camera lens covers is usually changed with the aid of utilising heat and prying them off, that means you don't need to disassemble the entire cell to exchange those covers.

Here’s a closer study the back of the display and the vegan leather-based back disguise. You'll become aware of the graphite film over the motherboard, that's used to assist fritter away warmth. Peel this movie off to proceed extra.

Eleven extra Phillips screws want to be eliminated to get right of entry to the internal resources. After doing away with those screws, disconnect the battery cable and different flex cables from the mainboard. The LED flash is placed on the canopy, and the flex cable for the telephoto lens necessities to be disconnected from the mainboard as properly.

The motherboard inside the Razr Plus 2024 is a twin-layer layout. On one aspect, which you could see the 50-megapixel frequent camera, that is the solely digital camera with optical graphic stabilization (OIS). There's a secondary microphone within the higher corner, an autofocus and faded sensor at the lower back, and a few copper tape on the shields to help in warmth dissipation. The SIM reader is situated on the opposite area, in conjunction with the proximity sensor and a 32-megapixel the front-going through digicam. There's also graphite movie and thermal paste at the to come back shields to guide transfer warmness.

Once the graphite film is peeled returned, one could see an aluminum plate on top of the RAM, that is seated on right of the processor. Here's a better look into the skinny aluminum plate and the RAM and processor meeting.

To put off the battery on the proper flip, there are no pull tabs to assist in prying it off. Instead, you can still want to apply some isopropyl alcohol round the sides of the battery and allow it sit down for approximately 30 seconds to a minute. This will assistance to weaken the adhesive underneath, making it more easy to pry the battery out.

Here’s a look into the primary battery, that is rated at one hundred fifty milliamp hours. The telephoto digicam is held in location with adhesive, with the intention to update it, you’ll desire to apply warmness and punctiliously pry it off. The same manner applies to the earpiece speaker discovered on the exact.

For the extent buttons, the flex cable is hung on with adhesive. If you need to replace this, you possibly can should pry off the flex cable from the body and cast off the rubber gasket that seals it within the frame. The fingerprint sensor additionally has a rubber gasket securing it in situation, so that you could exchange it, you’ll desire to cut out the gasket and pull the flex cable from the body.

There are seven Phillips screws on the lowest that desire to be removed next. After that, disconnect the lowest battery cable and the relax of the flex cables. To unlock and unencumber those flex cables, raise up the black latches.

Here's a inspect the instant charging coil and the NFC antenna on the bottom canopy. The light grey line you see is an antenna line.

For the lowest battery, the technique is almost like the correct: observe isopropyl alcohol round the edges to weaken the adhesive, making it less complicated to pry the battery off. This bottom battery is rated at 2950 milliamp hours. The flex cable for the folding display necessities to be peeled off from the subboard, that could now be lifted up and eliminated.

Taking a investigate the subboard, we see the critical microphone observed lower than a coated guard. Here’s a have a look at the opposite part of the subboard. The charging port has a red rubber gasket round the hole for added renovation in opposition t water and grime. This is the bottom speaker meeting, and the vibrator motor is situated inside the bottom corner, held on with adhesive.

For the ones fearful approximately placing the SIM ejector tool into the wrong gap, worry now not—equally the filters and microphones at the higher and bottom are seated above the holes, so they received’t get damaged.

If you need to replace the folding display screen, as soon as the flex cable is disconnected and peeled off from the subboard, you'll warmness up the plastic border at the entrance and pry it off. Then, follow warmness to the folding screen to loosen the adhesive under and carefully pry it off from the body. However, I'm now not going to pry off the folding reveal during this video because of the top hazard of adverse it and the magnitude of utilising the perfect adhesive for reapplication. It’s advised to decide on a alternative reveal that includes the body pre-attached to simplify the job.

These flex cables that connect the lowest 0.5 of the mobilephone to the suitable half are routed as a result of exact channels. There are covers protecting them in place at the side of screws and seals on major of those screws. You'll need to peel off the seals to remove the screws and covers. These black screws additionally have rubber-like seals for extra safe practices.

For the repairability ranking, I deliver the Motorola Razr Plus 2024 a five.5 out of 10. While it’s rather basic to disassemble, the inability of pull tabs for the batteries and the complexity of changing the folding display screen lessen its entire repairability.

Now it is time to place the cell lower back in combination. Reassemble all the pieces in https://gadgetkingsprs.com.au/ Phone repair Springwood reverse order, making sure all additives are securely reconnected. Once all the pieces is back in vicinity, chronic at the cell to affirm or not it's functioning as it should be.

Before we wrap up, I choose to present a particular shoutout to Gadget Kings PRS. If you’re in desire of nontoxic cell fix services and products, I distinctly advise checking them out at Gadget Kings PRS. They’ve helped me varied times and be offering greatest carrier. Don’t fail to remember to consult with their webpage for greater important points. I wish you discovered this teardown and disassembly instruction invaluable. If you probably did, please like the video, enroll in the channel, and hit the notification bell so you is not going to miss any of my long run uploads. Thanks for looking, and I'll see you within the subsequent video!